Revista de Odontologia da UNESP
https://revodontolunesp.com.br/article/588017307f8c9d0a098b45e1
Revista de Odontologia da UNESP
Original Article

Alterações verticais distais em prótese inferior de extremidade livre

Distal vertical changes in lower free-end prosthesis

Dolce Filho, P.; Sousa, V.; Gennari Filho, H.; Rodrigues, J.E.; Passanezi, R.; Held, C.M.

Downloads: 0
Views: 1001

Resumo

Foi estudada a flexão a que está sujeita a malha de retenção (retentor físico) metálica para casos de extremidade livre inferior durante a prensagem de resina acrílica. Após a desinclusão do aparelho, há liberação de tensões que podem provocar contatos prematuros principalmente na região de molares; assim foi constatado também a influência de "stops" ou suportes distais para essas malhas com a finalidade de evitar ou diminuir a flexão da liga metálica.

Palavras-chave

Prótese de extremidade livre, flexão de liga, alteração vertical

Abstract

To study possible distal vertical changes in lower free-end partial prosthesis, a rubber matrix of a patient class I lower dental arch, was made, from which 40 stone casts were obtained. Four chromium-cobalt frameworks were casts, being equal in design except the retentive framework. Two af them were 2/3 of the alveolar ridge in length, one presenting a distal "foot" and, the other not. The other two of the same lenght, too, but shorter than the two described before,one presenting a distal "foot" and the other, not. The flexion was recorded by a precise comparative device after a load of 500g was applied in three different points of the retentive framework. Accordtng to the data and statystical analysis it was possible to conclude that: 1) the distal stop ("foot") diminishes considerably the tensions an the retentive framework; 2) the shorter the retentive framework the less tension is exerted on the retentive framework.

Keywords

Prótese de extremidade livre, flexão de liga, alteração vertical

References



ASGAR, K. & PEYTON, F. A. 196!. Effect of microstruture on the properties of cobalt-base alloys. J. dento Res.,· 40:63-70·

BATES, J.F. 1965. Studies related to the fracture of partial dentures. Flexural fatigue of a cobalt-chromium alloy. Brit. dent. J., 118:532-537. 1965.

BOMBONATTI, P.E., GARLIPP, O.A. & BARROS, L. E. 1968. Resistência a flexões sucessivas de ligas de cromo-cobalto. Rev. paul. Cirurg. Dent., 22:241-245.

CARTER, T. J. & KIDD, J. N. 1965. The precision casting of cobalt-chromium alloy. Part. 2 - The influence of casting variables on mi· crostructure and mechanical properties. Brit. dento J., 118:131-431}.

EARNSHAW, R. 1961. Fatigue tests on a dental cobalt-chromium alloy. Brit. de.nt. J., 110:341-346.

HARCOUT, H. J. 1961. Fractures of cobalt-chromium alloy. Brit. dent. J., 110:43-50. McCRAKEN, W. L. 1964. Partial Denture Construction. 2a. ed. St. Louis, Mosby, p. 370-436.

MILLER, E. L. 1972. Removable Partial Prosthodontics. Baltimore, Williams & Williarps, p. 190-196.

SOUSA, V., BOMBONATTI, P.E. PIMENTEL, F., ARRUDA, J.L.M. & DOLCE FILHO, P. 1978. Flexão de ligas de cromo-cobalto com relalação à secção transversal e polimento. Rev. Fac. Odont. Araçatuba, 7:201-205.
588017307f8c9d0a098b45e1 rou Articles
Links & Downloads

Rev. odontol. UNESP

Share this page
Page Sections